decking and temperature

Over my career, I've built structures on three continents and in a wide variety of climate types. I've worked under the hot sun of Hong Kong, the dry desert of Arizona, in the long winters of Finland, and the rainy climes of the Pacific Northwest, but I haven't yet been in a place that combines elements of all of ...

Get Quotes

People ask how hot will their deck get this summer. I measured 63 synthetic deck samples in 16 product groups, with some surprising results....How hot a deck feels is a function of its surface temperature and its thermal conductivity.

Get Quotes

The size of the gaps required also depends on the temperature in which they're being installed so please check the Installation guide. All deck boards must always be installed with a 6mm side-to-side gap. The Hideaway Hidden Fasteners automatically measure the 6mm gap between grooved edge boards but ...

Get Quotes

Expansion and contraction are most significant where extreme temperature change may exist. Best practice is to cut and fasten the deck boards as soon after cutting as possible. When ambient temperature is above 32°F, install the boards together tightly at splices or miters. When ambient temperature is 32°F or below, ...

Get Quotes

After purchasing the material, store the composite decking flat and bundled, if possible, in the area where you will be cutting and installing it. The decking should be at the same temperature as the area where it will be installed. Working in the morning when the material is still cool will make your work much ...

Get Quotes

The Correct Temperatures for Staining Decks. It is important to know the tolerances a new deck stain will allow without hindering its performance. One of the most crucial areas of concern is with air temperature. Temperatures need to be in the safe zone while the deck stain is being applied and for 8-12 ...

Get Quotes

This research was done at 1:00p.m. in NW Portland, Oregon on 7-21-16 on a full sun day with no clouds. I used a laser thermometer which is a small hand held device that you point at a surface and it immediately gives you a reading of the temperature of that surface. Here are the results: The hottest was cedar decking that ...

Get Quotes

One kit—consisting of two 10-foot-long silicone-rubber thermal blankets and one control box—is required to bend a 10-foot-long plank; use two kits for a 20-foot-long deck board. Temperatures and times vary widely, but it typically takes about 35 to 55 minutes to heat an cellular PVC deck board to its ...

Get Quotes

Ensure a gap is left to allow for lineal expansion of the deck boards which is due to temperature changes from when laid. (Please see table below). Boards will not expand across the width or in the depth. Support. A minimum of 30mm of the end of the deck board must rest on the supporting joist. Use 2 joists to support ...

Get Quotes

Maximum allowable perpendicular overhang for is 102 mm. All decks require air circulation to keep them dry and looking good. To improve air flow, leave openings under the decking or increase gapping to. 10 mm. End-to-End End-to-Width. Gap decking end-to-end, based upon the temperature at installation.

Get Quotes

A fact not always considered when buying composite decking is that the structural strength of bamboo or wood plastic composite decking can be severely affected by temperatures over 40 Degrees Celsius, which can reduce its normal strength by up to 45 to 50%. This effect may have adverse effects, ...

Get Quotes

and temperatures between 40° - 90°F (4°C - 32°C). decking is not itself a food source but spilled dirt and debris from flowerpots and gutters can nourish mold. If the gaps between deck boards are too small or clogged, the decking can also supply moisture. Refer to gapping instructions on page 20. How to Remove Mold ...

Get Quotes

High temperatures are a big concern while applying the stain. If it's too hot, the stain may dry too quickly, potentially causing lap marks and uneven penetration. Avoid staining your deck if it's above 90 degrees Fahrenheit. To ensure this, either choose a cooler day or stain your deck in the morning before it ...

Get Quotes

Product Details

Product List