hardwood floor boards have holes

The rich patina of old wooden floorboards that are uneven with wear and have been scrubbed or polished for generations, contributes immensely to the ... Beetle infestation revealed by small holes and fine powder; Damp and rot; Loose boards and creaking or 'springy' floors; Gaps between floorboards ...

Get Quotes

You'll need to find which part of the floorboard is loose by walking over it and seeing where it moves. If the board is damaged and you can't re-nail in the old holes, you'll have to take the nails out with pincers and then lift the board to check for cables and pipes. Mark any you find on the board in pencil to show where they ...

Get Quotes

Clear grade means that all the natural marking in the wood have been cut out and removed. Clear grade boards therefore produce the cleanest looking flooring. In the reclaimed woods, there will be very few small nail holes and zero bolt holes in the wood. This grade of wood is often used in minimalist designs and ...

Get Quotes

Find your wood chisel to split the board. Along the line of holes that you have just drilled, use the chisel to break apart the board. You may want to use a rubber mallet to help apply enough pressure to break up the wood. This will make it much easier to get the board out in the next step.

Get Quotes

Rest the bar on a wood offcut to prevent the bar from damaging adjacent boards. Remove the tongue from the new board, using a sharp chisel (Image 4). If the boards are very thick, you may need to use a saw. Reposition the board in place (Image 5). Since blind nailing is not possible, use finish nails and fill the holes.

Get Quotes

Patch Flooring: Replace the missing floor boards with matching wood flooring of the same species and width. When possible use matching flooring from the house, such as that found in a closet or flooring that may have been removed during renovation; Sand and Refinish Floor: Sand and refinish the floor so the old and ...

Get Quotes

Whether you need to lift floorboards to inspect the pipes below, to fix a creaking board or replace a section that has split or warped with wear, the most important rule is never to nail or screw ... Drill pilot holes in the joist first or use 50mm countersunk screws with a 4-5mm gauge to avoid splintering the wood.

Get Quotes

Wood has grain; woodfiller does not, so large areas of woodfiller look nothing like the wood that surrounds it. Even when it does take on the color of the stain or finish you use, it will still look like a big, undifferentiated blob on your floor. When you use filler on nail holes and chipped board corners, it camouflages well in the ...

Get Quotes

woodfloorconservancy.org wood-... Floorwright Wood Floor Repair Instructional Video shows the Floorwright's Apprentice how to visually repair a board that cannot be sanded again. Category. Howto & Style. License. Standard YouTube License. Show more. Show less. Comments 7. Default profile ...

Get Quotes

dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2.

Get Quotes

As others have mentioned, wood filler cracks out and in some cases looks like cat litter after a while. The reason is that the wood expands and contracts as the humidity changes between the seasons. Replacing the boards is not as difficult as it seems, but the repairs will stick out unless you refinish that ...

Get Quotes

Laying a solid wood floor is a job that can quite feasibly be carried out on a DIY basis, but obviously not everyone has the time or inclination to do this. ... When you get to pipes, mark the position on the board that is being laid around it, drill a hole about 5mm larger than the diameter of the pipe, and make ...

Get Quotes

Although significant gaps in relatively new wood flooring are relatively uncommon along the lengths of the board, you may find that newer floors develop gaps at the ends of the boards. Old floors on the other hand are likely to have gaps, both along the lengths of the boards as well as at the ends, due to the ...

Get Quotes

Replacing damaged or hole-filled hardwood tongue-and-groove floorboards takes a couple of hours, sharp tools and an understanding of how to break the interlocking ... refinished. Otherwise, using belt and orbital sanders, you'll have to level and then finish the new plank so it blends into the existing flooring—a tough job.

Get Quotes

To fill these holes you'll need a plug cutter, cordless drill, and a hole saw or spade bit. If you've got old wood planks from the originally flooring then you are in luck, otherwise you'll need to find a replacement somewhere else. You could always cut a out of the existing floor somewhere out of the way, like a ...

Get Quotes

I have several holes in my hickory hardwood flooring. ... Steam will break down the finish on the sides of the boards and start chipping peeling off. .... to fill a gouge or nick in my floor board ( fake oak) take another board from my supply in garage and sand off some of the color into the hole and fill with epoxy.

Get Quotes

lyctid beetle emergence hole in oak. Round emergence hole in oak flooring. These holes often have fine, powdery wood particles around them. The ruler marks are 1 16" apart.

Get Quotes

Product Details

Product List